Insert Bleeding Edge tool in to hole, and push in until you feel and hear a snap.Ħ. Remove rubber caliper bleed plug by hand.
#Sram bleeding edge full
Thread and nip tight the ¾ full lever syringe into lever bleed port.ĥ. Remove lever bleed port screw using Torx T10 and place to one side. Adjust brake lever position so the tip of the lever is 75-80mm from the centre line of the handlebar.Ĥ. Top tip: When filling syringes, make sure the tube end is fully submerged in oil to prevent any air bubbles entering.ģ. Fill lever syringe ¾ full of brake fluid and close syringe clamp. Add small amount of DOT 5.1 brake fluid to caliper syringe. Fit lever bleed tool and Bleeding Edge tool to syringes. Fit bleed block to caliper and turn pad contact adjuster in opposite direction of arrow until it stops.Ģ. It can actually strip paint, so wipe away any spillage as quick as possible! Also ensure you have removed all remnants of brake fluid before fitting the brake pads and wheel back in to position, the smallest amount of oil will contaminate the braking surfaces and is almost impossible to remove.ġ. It’s recommended that you wear nitrile gloves when handling DOT brake fluid due to its corrosive properties. SRAM brakes that use Bleeding Edge also have an improved oil path through the caliper to further help with the bleeding process – all the compatible models can be found on the SRAM website. The Bleeding Edge tool also allows the caliper bleed port to be closed off before the syringe is removed, eliminating oil spillage and reducing clean up. It’s simple and incredibly easy to fit and gives a defined snap to tell you it is correctly inserted in place. The idea is to reduce the amount of fuss and mess when carrying out a successful brake bleed.īy utilising a quick and simple pop on/off bleed-port interface, Bleeding Edge minimises the chance of air sneaking in to the system. Most new SRAM disc brakes are designed with a specific bleed port in the caliper to be used with a Bleeding Edge tool. Tools needed: SRAM brake bleed kit with bleeding edge tool, DOT 5.1 brake fluid, bleed block, T10 Torx, 2.5mm Allen key, rag, isopropyl alcohol/brake cleaner, nitrile gloves.Īlthough this video below doesn’t show the Bleeding Edge adaptor tool it does still contains essential need-to-know methodology.
#Sram bleeding edge how to
Push on the syringe, release the syringe to equalize, and you are ready to clip the hose, remove the syringe and replace the bleed port screw.We show you how to take the blood, sweat and tears out of the Avid and SRAM brake bleed process using the Bleeding Edge adaptor tool.Repeat these steps until there are no more bubbles. Let the syringe equalize and then pull and release the brake lever 10 times.
![sram bleeding edge sram bleeding edge](https://www.mtb-mag.com/wp-content/uploads/2017/11/IMC4015-1600x1067.jpg)
Then pressurize by pushing on the syringe. Pull on the syringe to create a vacuum, drawing air out of the system.
![sram bleeding edge sram bleeding edge](https://mbaction.com/wp-content/uploads/2016/03/Garage-20-e1457313959384.jpg)
![sram bleeding edge sram bleeding edge](https://cdn.shopify.com/s/files/1/0269/4791/1754/files/sram-bleeding-edge-tool.jpg)
#Sram bleeding edge skin
Mixing fluids can cause damage to components and lead to brake failure, which is dangerous.ĭOT fluid is corrosive, and it can irritate the skin and eyes, and damage paint and other finishes - so it is important to take care. Never share bleed kits between DOT fluid and mineral oil systems. Never use mineral oil in brakes designed for DOT brake fluid, or vice versa. It is important to always use the appropriate brake fluid for the brake being serviced. If in doubt, or if this procedure is not working, contact the brake manufacturer for model-specific information.
![sram bleeding edge sram bleeding edge](https://cdn.mos.cms.futurecdn.net/6bKoZFxcYepVjKqkhtg5pZ-650-80.jpg)
See this article for the Bleeding Edge procedure.īrake bleeding is considered an advanced service procedure, and requires a thorough technical knowledge of the braking system. This bleeding procedure will work on SRAM drop bar and flat bar brakes that do not feature Bleeding Edge.